Illustrative photo of a plumber repairing a residential gas water heater

Frisco · Collin County · North Texas

Water Heater Repair in Frisco, TX

Hot water back, without the runaround.

Gas, electric and tankless water heaters repaired and replaced by Texas-licensed plumbers, across Frisco and the cities around it.

Call about your water heater(972) 945-6903

Typical prices are on the site, and yours is confirmed before work starts.

Tell us what is going on.

✓ Texas-licensed plumbers✓ Gas, electric and tankless✓ Permit included on replacements✓ Open 24/7

What is your water heater doing?

Common water heater problems we fix

No hot water

On a gas heater, usually the pilot, igniter or thermocouple. On electric, a tripped reset, an element or a thermostat.

What to check first

Leaking

A valve or fitting can be fixed. Water from the tank itself means a new heater. Shut the cold water off at the top.

Leaking water heater

Not enough hot water

Sediment from hard water, a failed lower element, a broken dip tube, or a heater too small for the house.

Flushing and sediment

Popping or rumbling

Sediment on the bottom of the tank. A flush usually quiets it; on an old tank, it can mean the end is near.

Water heater flush

Pilot will not stay lit

A worn thermocouple or flame sensor, a dirty burner, or a clogged air intake screen under the tank.

Gas water heater repair

Tankless error code

Most often scale in the heat exchanger, a dirty inlet filter or an ignition fault. A descale fixes many.

Tankless repair

Repair or replace?

What water heater repair costs in Frisco

Most repairs are a single part. A thermocouple or flame sensor typically runs $150 to $325, a heating element $175 to $400, and a gas control valve $300 to $650. If the tank itself is leaking, or the heater is past ten years and the repair would cost more than about half a new one, replacing it is usually the better money. A new 50-gallon gas heater typically runs $1,800 to $3,000 installed, permit included.

See every price or read about water heater replacement.

Typical tank life8–12yearsLess with hard water and no flushing

Water heater repair prices

RepairTypical price, parts and labour
Thermocouple or flame sensor (gas)$150 to $325
Pilot assembly or igniter (gas)$175 to $400
Gas control valve (gas)$300 to $650
Heating element (electric)$175 to $400
Thermostat (electric)$150 to $350
Temperature and pressure relief valve$150 to $300
Anode rod$150 to $350
Dip tube$150 to $325
Drain valve$125 to $275
Water supply lines or shut-off valve$150 to $350

Typical prices around Frisco in 2026, to help you plan. Your price is confirmed with you before any work starts.

North Texas water

Why water heaters wear out faster around Frisco

Frisco's water comes from North Texas lakes and is moderately hard. Heated, the minerals drop out as sediment on the bottom of a tank, or as scale inside a tankless unit. That is the popping noise, the shrinking hot water supply and many tankless error codes. A yearly flush, an anode rod check every few years and water pressure under 80 psi are the things that make a heater last.

Many Frisco homes have the water heater in the attic, where a leak does the most damage. If yours is up there, check that the drain pan and its drain line are clear.

Water heater flushing and maintenance
Illustrative photo of a gas water heater installed in a garage

How we can help

Water heaters first, and the rest of the plumbing too

How it works

  1. Call or send the form. Tell us what the heater is doing, and its age if you know it. A photo of the label helps.
  2. A licensed plumber comes out. They find the fault and give you the price before any work starts.
  3. Fixed, or replaced. Most repairs are done on the first visit. Replacements include the permit, a drain pan and haul-away.

Frisco Water Heater Repair arranges every job with Texas-licensed plumbers and stays your point of contact from the first call to the finished work.

Helpful answers

Questions people ask

How much does water heater repair cost in Frisco?

Most water heater repairs in Frisco run $150 to $325 for a thermocouple or flame sensor up to $300 to $650 for a gas control valve. Electric heating elements typically run $175 to $400. You get the price before the work starts.

Should I repair or replace my water heater?

Repair it if it is under about eight years old and the fault is a part, such as a thermocouple, igniter, element, thermostat or valve. Replace it if the tank itself is leaking, the water is rusty, or it is past ten years and the repair would cost more than about half a new heater.

How much is a new water heater in Frisco, TX?

A 40 or 50-gallon gas water heater typically costs $1,600 to $3,000 installed, including the city permit and haul-away. A gas tankless unit runs $3,500 to $6,500.

What areas do you serve?

Frisco and the cities around it, including Plano, McKinney, Allen, Prosper, Little Elm, The Colony, Celina, Lewisville, Carrollton and more across Collin and Denton counties. See the service area page for the full list.

See all 8 frequently asked questions

Cities we cover around Frisco

Also covered: Hackberry, Oak Point, Cross Roads, Aubrey, Parker.